Vision VISION-64 Guide de l'utilisateur télécharger pdf (Page 16)

Vision-64 User Guide

Issue 1.02

Zone 1 Name Z001 is

bypassed. To un-bypass,

press OFF.

Press OK or MENU

If the zone is not bypassed, the keypad will prompt:

Zone 1 Name Z001 is

un-bypassed. To bypass,

press ON.

Press OK or MENU

3. Press [ON] or [OFF] to toggle the zone to be bypassed/un-

bypassed.

4. Press [OK] to save and exit, or press [MENU] to exit without

saving.

Repeat steps 1 to 4 to bypass or un-bypass additional zones.

Inputs > Commands >

Set Chime Zones

MENU 3-0-3

This menu allows you to program zones to be monitored when the

system is turned off. Chime mode is ideal to monitor a front door

to sound the keypad buzzer when opened (faulted).

1. Enter [MENU] + [3] + [0] + [3].

A list of areas will display on the keypad.

2. Use the [

] and [] keys to select the area that you want

to program zones for chime mode, then press [OK].

Alternatively, you can enter the area number that you want

to program chime zones, then press [OK].

The keypad will list all zones that can be programmed for

chime mode. A ‘’ displayed on the right side of the zone

name indicates that the zone is already set for chime.

Z001 Zone 1 Name 

Z002 Zone 2 Name

Z003 Zone 3 Name

Press  OK or MENU

3. Use the [↑] and [↓] keys to select the zone that you want to

set for chime, then press [OK]. Alternatively, you can enter

the zone number that you want to set for chime, then press

[OK].

If the zone is not programmed for chime, the keypad will

prompt:

Zone 1 Name Z001

Zone Chime is OFF,

To turn ON, Press ON.

To Go Back Press OK

If the zone is programmed for chime, the keypad will

prompt:

Zone 1 Name Z001

Zone Chime is ON.

To turn OFF, Press OFF.

To Go Back Press OK

4. Press [ON] or [OFF] to toggle the zone to be monitored

when chime mode is turned on.

5. Press [OK] to save and exit, or press [MENU] to exit without

saving.

Inputs > Commands >

Set Part 2 Zones

MENU 3-0-4

This menu allows you to program which zones are to be monitored

when an area has been turned Part 2 On.

1. Enter [MENU] + [3] + [0] + [4].

A list of areas will display on the keypad.

2. Use the [

↑] and [↓] keys to select the area that you want to

program zones for Part 2 On, then press [OK]. Alternatively,

you can enter the area number that you want to program

Part 2 On zones, then press [OK].

The keypad will list all zones that can be programmed for

Part 2 On. A ‘’ displayed on the right side of the zone

name indicates that the zone is already bypassed.

Z001 Zone 1 Name 

Z002 Zone 2 Name

Z003 Zone 3 Name

Press  OK or MENU

3. Use the [↑] and [↓] keys to select the zone that you want to

set for Part 2, then press [OK]. Alternatively, you can enter

the zone number that you want to set for Part 2, then press

[OK].

If the zone is not programmed for Part 2, the keypad will

prompt:

Zone 1 Z001

Is not a PART2 Zone,

To Enable, Press ON.

To Go Back Press OK

If the zone is programmed for Part 2, the keypad will

prompt:

Zone 1 Z001

Is a PART2 Zone,

To remove, Press OFF.

To Go Back Press OK

4. Press [ON] to monitor the zone when the area is turned Part

2 On, or press [OFF] so that you do not monitor the zone

when the area is turned Part 2 On.

5. Press [OK] to save and exit, or press [MENU] to exit without

saving.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Vision VISION-64 Guide de l'utilisateur Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Vision VISION-64