Vision VISION-64 Guide de l'utilisateur télécharger pdf (Page 14)

Vision-64 User Guide

Issue 1.02

Areas > Commands >

Turn Area On/Off

MENU 2-0-1

This menu allows you to turn an area All On or off.

1. Enter [MENU] + [2] + [0] + [1].

A list of different areas will display on the keypad.

A001 Reception Area

A002 Sales Dept 

A003 Administration Dept

Press , OK or MENU

If an area has already been turned All On or Part On, a

‘tick’ () will be displayed on the right side of the name

description (see A002 Sales Dept above).

2. Use the [

↑] and [↓] keys to select the area that you want to

turn on or off, then press [OK] to select. Alternatively, you

can enter the area number you want to turn on or off, then

press [OK].

Areas > Commands >

Turn All Areas On

MENU 2-0-2

This menu allows you to turn on all areas that your PIN has been

assigned to at the same time All On. The keypad display below

shows the area icons 1 through to 8.

1. Enter [MENU] + [2] + [0] + [2].

The keypad will display the exit time bar to prompt you to

exit all areas. You should leave all areas now.

Area 1 Name

EXIT

NOW

When exit time has expired, the keypad will display that all

areas are turned All On (Armed).

Area 1 Name

ARMED

Fri,Aug,13 5:34 pm

Note:

Area icons will only display if programmed to

do so by your security installer.

Note: Area icons will only display if programmed to do

so by your security installer.

Areas > Commands >

Turn All Areas Off

MENU 2-0-3

This menu allows you to turn off all areas that your PIN has been

assigned to at the same time. However, this menu requires at least

one area that has a keypad assigned to it to be disarmed before you

can access this command.

1. Enter [MENU] + [2] + [0] + [3].

Areas > Commands >

Move To Area

MENU 2-0-4

This menu allows you to operate multiple areas from the same

keypad when the system has been partitioned. Before operating a

different area, you will need to move the keypad to the area that

you want to operate.

1. Enter [MENU] + [2] + [0] + [4].

A list of different areas will display on the keypad.

A001 Reception Area

A002 Sales Dept

A003 Administration Dept

Press , OK or MENU

2. Use the [↑] and [↓] keys to select the area that you want

to move the keypad display to, then press [OK] to select.

Alternatively, you can enter the area number that you want

to move the keypad display to, then press [OK].

Areas > Commands >

Chime On/Off

MENU 2-0-5

Chime mode allows you to monitor a zone (or group of zones)

to sound the keypad buzzer or activate a programmable output

when the corresponding area is turned off (disarmed). This can

be useful when you need to monitor the front or back entrance to

the premises.

This menu allows a user to turn chime mode on or off. Only

keypads programmed to sound the chime tone will be heard when

a zone programmed for chime is faulted.

The master user can Set Chime Zones on page ????. This allows the

master user to program which zones can be monitored for chime.

1. Enter [MENU] + [2] + [0] + [5].

A list of different areas will display on the keypad.

A001 Reception Area 

A002 Sales Dept

A003 Administration Dept

Press  OK or MENU

2. Use the [↑] and [↓] keys to select the area that you want

to turn chime mode on or off, then press [OK] to select.

Alternatively, you can enter the area number that you want

to turn chime mode on or off, then press [OK].

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Vision VISION-64 Guide de l'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Vision VISION-64